How to Install Wood Effect Venetian Blinds

How to fit a Wood Effect Venetian Blind

Drill Bits / Fixings

Drills & Tips:

Use an undersize drill bit on your first hole to see what type of fixing you will require, a push fit Rawlplug is best (not an oversize hole).

(1) φ5.5mm Tungsten tip Masonry Drill Bit, this drill bit will only fit SDS Drills, it is a powerful drill, however it is not a problem if you have a conventional hammer drill it just takes a little longer to drill the holes. See (fig 2) below.

(2) Standard φ5.5mm Tungsten tip Masonry Drill Bit fits conventional drills.
Tip: We find it is better to use a φ5.5mm drill bit rather than the recommended φ6mm drill bit with the Red Rawlplug (fig 6). As generally you tend to end up with a slightly oversized hole, the trick is to avoid this; you can always re-drill the holes with the φ6mm drill bit if the holes are too small, once you have drilled the pilot holes. Try to achieve a good push fit with the Rawlplug (fig 6), use (No6 or 8) x 32mm long Prodrive Woodscrews (fig 9,10).

(3) High Speed Twist Drill Bit φ6.0mm HSS. This drill bit would be used for the Fischer Plaster Plug (fig7) i.e. use for plasterboard and hollow fixings. TIP: Tight fit with plaster plug use (No6 or 8) x 32mm long Prodrive Woodscrews (fig 9,10).

(4) High Speed Twist Drill Bit φ3mm HSS. This drill bit would be used if you have a steel lintel. TIP: Use a little oil on the tip of the drill, 3 in 1 or something similar to help lubricate the cutting action and save the tip of the drill, be patient apply firm even pressure, give the drill bit time to cut through the metal too much pressure and the drill bit will snap, release the pressure as it breaks through, it is not the same as cutting masonry do not use the hammer action with HSS Drill Bits. Pre drill the plaster first with masonry drill bit to save the HSS Drill Bit tip.
Use Self Tapping Prodrive Screws the length will depend on the distance to the lintel (No 6) Self Tapping Screws 20-32mm long (fig 11,12,13).13 is a No8 Screw and would need a φ4mm drill bit.

(5) Carbide Tipped Drill Bit for drilling tiles φ8mm. TIP: Apply some masking tape to the face of the tile to prevent the drill slipping on the first initial cut, drill a φ8mm hole in the tile only, then change to the φ 5.5mm masonry Drill Bit (fig 2,1) to drill the remainder of the hole. Use Red Rawlplug (fig 6) or Fisher Plaster Plug (fig 7) dependant on your lintel type i.e. concrete, metal or is it hollow? Use the same method as described above for fixings, the φ8mm larger hole in the tile will prevent the tile cracking when the Rawlplug expands with the screws.

Fixings

(6) Red Standard Rawlplug use 32mm long size (No6 or 8) Prodrive Woodscrews (fig 9 or 10) φ5.5mm Drill Bit (fig1 or 2).

(7) Fischer Plaster Plug (LDF) for plasterboard & hollow fixings with gaps of 2.5cm or more between plaster and lintel, use 32mm long, size (No6 or 8) Prodrive Woodscrews (fig 9 or 10) φ6.0mm Drill Bit (fig3). (Remember tight fitting hole).

(8) No6 20mm long Woodscrew Prodrive for Wood and PVC fixings.

(9) No6 32mm long Woodscrew Prodrive use with Red Rawlplug φ5.5mm Drill Bit or Fischer Plaster Plug φ6.0mm Drill Bit.

(10) No8 32mm long Woodscrew Prodrive use with Red Rawlplug φ5.5mm Drill Bit or Fischer Plaster Plug φ6.0mm Drill Bit.

(11) No6 20mm long Pan Head Self-Tapper Prodrive use for PVC & metal fixing, HSS Drill Bit φ3mm.

(12) No6 32mm long Pan Head Self-Tapper Prodrive use for metal fixing, HSS Drill Bit φ3mm.

(13) No8 32mm long Pan Head Self-Tapper Prodrive use for metal fixing, HSS Drill Bit φ4mm.

All fixings drill bits and tools can be purchased at any good tool merchants, B,Q ,or Screwfix.

Please note: The fixings we provide with your blinds may not be suitable for your particular installation; it is not possible to provide all fixings for every situation please use the guides above, to determine the best method and fixings to use, for each blind you are installing.

Outside Recess (face fix)

If your blind is to be fitted on the outside of the recess, measure the blind (B) and the width of your window (A). Deduct A from B and divide by two to give you the measurement of each side of the window (C) - this is the position your blind will sit between. Mark off how far above the window the blind position will be (D) - we advise 4cm in the how to measure section.

You need to position the brackets in the headrail as near to the ends as the mechanism will allow - approx 8cm. For centre support, you need to add one to the middle if the blind is over 1.5m, again as near to the centre as the mechanism will allow. With the brackets temporary fitted, offer the blind up to the pencil marks on the outside of the recess.

Mark on the wall the position of the brackets, making sure the blind is level. Remove the blind and the brackets and mark through the two holes for each bracket position. Drill and fix the brackets and open the swing arm to the right. Place the front lip of the headrail into the bracket first and then ease the back in. Move the arm to the left until it meets the headrail of the blind to lock into place the window frame.

Inside Recess

Decide if you are going to face fix or top fix - we would advise top fix if you have handles. Simply measure the distance of your handles from the frame and allow an extra 10mm, this will be your measurement from the window frame.

Follow the instructions for the position of the brackets in the headrail in the outside recess fitting instructions. Offer the blind up to the inside top of your lintel, centre the blind and mark the bracket positions on the lintel. When marking the hole position, ensure the back of the bracket is nearest your pencil mark and drill - as in the outside recess fitting.

Operating Your Blind

Insert the plastic wand hook into the eye in the headrail, the wand rotates to open and close the slats. The pull cord is for raising and lowering. Pull the cord to the desired position and move cord across the face of the blind to lock into position. To unlock do the reverse, allowing the cord to slip through your fingers. Always have the slats in the open position before raising and lowering.

Cleaning

Clean your blind with a dry or damp cloth or brush attachment with your vacuum cleaner.

Window Blind Cord Safety

Simple precautions to significantly reduce the risk.

Whilst window blinds and window furnishings are not inherently unsafe and many millions are sold every year, there have been instances of injury and child deaths involving accidents with window blind and window furnishings cords and chains. The cleats listed below are offered as an option at the time of placing your order, and will match to your blind type.

WARNING

In the interest of safety, please keep all pull cords and chains out of the reach of children. Move cots beds and other furniture away from blinds and install safety devices, such as cleats and cord tidies, to limit access to cords. Hanging cords can be a potential risk to children, so the greatest care needs to be taken at all times.

CLEAT

This safety device would be most appropriate for blind types listed below.

Wooden Venetians, Aluminium Venetians, Pleated, Woven Wood, Roman standard cord and cleat type.

Cleat

This should be securely fixed to an adjacent wall, out of the reach of children, and the cord/chain secured as shown, after each operation of the blind.

Fitting

If you have requested a child safety cleat with your blind, and for some reason you can not find it please contact us to request a replacement, before fitting your blind.

Screw the cleat to an adjacent wall at the required height. Wind the cord around the cleat in a secure figure-of-eight.

These instructions can also be found within the installation guides provided at time of purchase.

Use of additional safety devices may reduce the risk of strangulation or injury but cannot be considered foolproof. Persons in charge of children and vulnerable people are ultimately responsible for following the safety instructions provided by us the manufacturer.